Heating in Tbilisi and Georgia: How Apartments Are Heated
Most apartments in Tbilisi have no central heating. It stopped working in the 1990s, and since then every apartment has heated itself. New buildings are no different: they are handed over without a heating system, and the owner designs and installs one. If you are thinking about heating in Tbilisi, below are the options, what a system is made of, and what needs deciding before the renovation starts.
Heating in Tbilisi: the main options
A gas boiler and a water system. The most common setup. A wall-mounted boiler heats water, which runs through pipes to radiators, convectors or underfloor heating. A combi boiler also heats water for the kitchen and the shower. If the apartment has a gas supply, this is usually the most economical way to heat it through the season.
An air conditioner on heating mode. An inverter split system goes in quickly and costs less up front. It works well in spring and fall, but in frosty weather it gives less heat, pushes warm air up to the ceiling, dries it, and leaves the floor cold. As the only source of heat in Tbilisi it is a poor fit.
Electric heaters and electric underfloor heating. Handy for spot use: in a bathroom, a kitchen, a room you rarely use. As the main heating they are expensive to run.
A heat pump. High efficiency and low running costs over the season, but the equipment is expensive. You see it more often in private houses than in apartments.
What a water heating system is made of
It helps to think of the system in three parts:
- The heat source: a boiler (or a heat pump). Its output is chosen from the apartment's heat loss, not eyeballed from the floor area.
- The pipework: pipes from the boiler to every room. They are laid in the screed or in the walls before the finishing work.
- The heat emitters: what actually gives heat to the room. Radiators, in-floor and free-standing convectors, underfloor heating. They decide whether it is warm by the window and how the unit looks in the interior.
The boiler and the pipes are usually chosen by the installer. The emitters are worth choosing yourself: they are what you see every day, and they are what decides whether you feel a draft from the window.
What to install, and where
| Where | What works |
|---|---|
| Floor-to-ceiling window, full glazing | An in-floor convector along the whole window |
| Floor-to-ceiling window, more heat | A convector with a fan, 1.5 to 3 times more powerful |
| Window with a sill, ordinary wall | A radiator or a free-standing convector |
| Bathroom, kids' room, warmth underfoot | Underfloor heating, together with convectors at the windows, not instead of them |
The main rule: heat goes where the cold gets into the room, which means under the windows. Cold air slides down the glass to the floor, and a unit under the window catches it. If the windows run to the floor, there is nowhere to hang a radiator, and that is exactly what in-floor convectors are for. The difference is covered in more detail in our guide on the in-floor convector vs radiator question.
Planning heating in a new-build apartment
Apartments in Tbilisi are often sold in "black frame" (a bare concrete shell) or "white frame" (rough work done, ready for finishing), with no heating system. The order of work that saves you from redoing things:
- A heat loss calculation from the plan. Floor area, ceiling height, glazed area, how many walls face outside. That gives the output each room needs.
- Choosing a unit for each window. This is where you decide which windows get in-floor convectors, where the radiators go, and where the underfloor heating goes.
- A boiler sized to the total output, with headroom for hot water.
- Pipework and the in-floor convector housings go in before the screed. The convector is recessed into the floor, and its height is allowed for in the screed thickness. Once the screed is poured, the only way to fit one is to break open the floor.
- Finishing work, then the grilles and the connection of the units.
If you are at the rough-work stage, this is the best time to send us the plan: we will pick a unit for each window and tell you how much depth to leave in the screed.
What the units cost
A guide to our prices as of November 2026, VAT included:
- In-floor convector: from 803 GEL per unit; the price goes up with the length and height of the housing.
- In-floor convector with a fan: from 1,328 GEL.
- Steel tubular radiator: from 462 GEL per radiator; a 1.5 kW radiator starts at 1,035 GEL. The detailed breakdown is in our article on heating radiators in Tbilisi.
The boiler, the pipes and the installer's labor are priced separately and depend on the apartment, so only a calculation from the plan gives an exact estimate.
Who does the installation
We select and size the units, supply them, and stay in touch at every stage. The system as a whole, meaning the boiler, the pipework and the connections, is installed by trusted installer partners we work with in Tbilisi and Batumi. If you already have your own installer, we will give them the installation diagrams and the product data sheets. Batumi has a climate of its own, and it has its own article: heating in Batumi.
In short
Tbilisi has almost no central heating, and every apartment heats itself. The main option is a gas boiler with a water system; an air conditioner works well as a supplement. Heat emitters go under the windows, and if the windows run to the floor, into the floor. In-floor convectors are planned before the screed.
Send us the apartment plan or the window dimensions, and we will pick the units, work out the output and the cost free of charge, and point you to an installer. Get in touch.
Frequently asked questions
- Is there central heating in Tbilisi?
- In most buildings, no. Central heating stopped working in the 1990s, and since then every apartment has heated itself: most often with a gas boiler feeding radiators, convectors or underfloor heating. New buildings are the same: the system is individual, and the apartment owner puts it in.
- Which is cheaper to run, a gas boiler or an air conditioner?
- If the apartment has a gas supply, water heating from a gas boiler usually costs less over the season and gives more even heat. An air conditioner is cheaper to buy and handy in spring and fall, but in frosty weather it gives less heat, creates drafts and dries the air. Many people combine the two: the boiler as the main heating, the air conditioner for summer and mild days.
- When in a renovation do I need to think about in-floor convectors?
- Before the screed is poured. The convector housing is recessed into the floor, so its height has to be allowed for in the screed thickness, and the pipes are run to it in advance. Once the screed is down, the only way to fit a convector is to break open the floor.
- Do you install heating systems?
- We select and size the units, supply them, and advise you at every stage. The system as a whole, meaning the boiler, the pipework and the connections, is installed by trusted installer partners we work with in Tbilisi and Batumi. You can also use your own installer: we will give them the diagrams and the product data sheets.